So the first thing you’re going to do is remove the pump from the system. The following eight simple steps will help you fix a worn-out Pump. Fixing a Worn Out Pump in a Fog Pump MachineĪ voltage pump is used in a fog machine, and it is responsible for pumping the loop liquid from the reservoir into the pump and subsequently into the heating element. Of course, if you’re not hearing any buzzing at all, the coils and your pump have likely shorted out and become too hot to function properly, and it will no longer function well at all. Once you’ve taken it out, you’ll notice that there’s another spring attached to a plunger-type component.Ĭonsequently, now that your pump is entirely disassembled, you can soak all of the parts and thoroughly clean them before reinstalling them. That thing can be pulled out and tapped, and there’s a spring inside of it.įollowing the removal of the screwdriver from the hole, you’ll discover that there’s a plastic piece in there that’s threaded, allowing you to just insert your screwdriver and turn it. You will notice a little ring emerge from the hole. Look closely and you will notice another portion of the ball rolling away from the ball. It’s a little more difficult this time.Ĭarefully tap the screen to make that small ball fall out. Once you’ve completed that, you may proceed to set the right side. It could be a good idea to disconnect the metal component and soak it in distilled water for a while. The pump mechanism, which is the object that the magnet causes to slide up and down and back and forth, sucking the fog fluid through, will be seen once the seal has been removed. Step 4: Disassemble and Clean the Pumping System If you lose these, the pump is no longer functional. Push down into the keyed groove, then push and twist, and when you’ve done that, carefully pull the keyed groove apart, making sure that no loose bits or the glass ball are lost. Remove the two screws from their positions and you’ll find a small key groove. Check to see if there is anything wrong with the coil in question. The pump pushes the fog fluid through and out of the system. You will notice a coil inside the pump that generates a magnetic field and that corresponds with a piece of metal that moves up and down once it is delivered. Step 3: Open the Interior of the Pumpīecause clogging can occur in a variety of locations if that does not resolve the problem, remove the two screws from the cylindrical pump assembly. When you see a flow of air, you’ll know you’re in good shape. To unclog it, poke it with a needle on both sides and immerse it in hot distilled water for a few minutes. That’s what’s causing your fog pump assembly to become clogged. So obtain a wrench and check to see if it’s loose, and then disassemble the device. That is the first and most important step. This should be carried out with care.Ī common problem with clogged pumps is that the nozzles of the pumps become clogged. So, in the case of a clogged machine, the first thing you should do is remove the rubber bracket that holds the fog machine together. Step 2: Check the Nozzle and Unclog the Pinhole If the heater is not giving out the right amount of heat this will not produce smoke and will need a fix. There are also some sensors for the heater block to make sure the fog machine is at the right temperature. There’s only one thing going on in there: the tube that comes down and goes into the pump, which then pumps out via a metal tube into the heater. Some things are going on in the machine that you can see. You will have access to the fog machine as soon as you remove the cover. You must first unscrew the compression fitting on the top, which is where the real tube is inserted. Unscrew the screws along the side of the case and lift the lid off. Here are four easy steps to unclog and clean your fog machine Pump Step 1: Open and Remove the Cover of the Pump When you have a blocked pump, the problem is that when you press the button, it creates a humming sound, which means that you can hear the pump running but no fog is coming out of it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |